SFC series 1.5”tri Clamp Fitting micro bubble diffuser stone for beer brewing
HENGKO Diffusion stones are used in the brewing industry for wort aeration prior to fermentation and carbonation before bottling.
Tri-Clamp 1.5" Diffusion Stone
Sintered stainless steel SFC series 1.5” tri Clamp Fitting micro bubble nano hydrogen ozone oxygen generator diffuser air stone for beer brewing
Force carbonating beverages.
Set your regulator to about 2 psi, and the gas will be forced through the millions of tiny pores in the stone, which dissolves the gas into the liquid. Your beer will be carbonated overnight.
You will need a homebrew kegging outfit with a CO2 tank, regulator, lines, and a keg. Simply attach a 24" length of ¼” ID tubing to the gas side dip tube of your keg with a worm clamp. On the other end of the tubing, attach the diffusion stone using another clamp. There are charts available online and in books for exact levels of temperature and CO2 pressure to achieve desired carbonation levels. Following is an example of average carbonation in beer: Chill the beer to 40 F. Adjust the regulator to 2 PSI and attach the gas disconnect. Every 3 minutes increase the pressure by 2 PSI until 12 PSI is reached. At this point, the beer will be carbonated, but it won’t hurt to leave it alone in the refrigerator for a few days under pressure.
How to use the diffusion stone
1. The “stone” sits inside the keg near the bottom.
2. A hose barb attaches it to a length of tubing (generally about 2 feet of 1/4” ID thick wall vinyl hose) which is affixed to the short downtube under the “in” or “gas side” post.
3. When the CO2 is connected, it sends a tremendous number of gas bubbles out through the beer. The minuscule bubbles create a huge amount of surface area to help absorb CO2 rapidly into the beer. This is actually a miniature version of a device used by commercial breweries everywhere.
4. Carbonation should be virtually instantaneous, though the manufacturer recommends carbonating your beer at least a few hours before serving.
◆ HENGKO SS air stone is commonly used to aerate the wort before fermentation, which helps ensure a healthy start to the fermentation process. The HENGKO 2.0 micron oxygen stone can be used to oxygenate wort using an oxygen regulator. The holes in the 0.5 stone are too fine to use to aerate the wort with an aeration pump.
The 2-micron HENGKO inline carbonation stone has millions of tiny pores so that this diffusion stone will quickly oxygenate wort & carbonate beer/soda prior to fermentation, to lower fermentation times & not easily get clogged.
Different micron stones produce very small bubbles, which are ideal for efficient absorption of the gas into your wort.
The most common use for this specific stone is to build an inline oxygenation assembly where the stone is threaded into a 1/2" NPT TEE, so chilled wort passes the stone on the way to the fermenter. It's important to limit the flow of oxygen in this setup to avoid over-saturating the wort.
HEGNKO diffusion stone can be installed into the 1/2″ FPT fitting or 1/4″ diameter,1/4" barb, or another custom connector, to connect with compressed oxygen tanks, air pumps, or kettle&wort chiller by hose.
The detail attention :
After carbonation, you can shake the beer keg. If do that, your beer can reach the best mouth-feel. high gravity beers may require more time because oxygen does not dissolve as easily in liquids with high specific gravity.
It's important to clean and sanitize diffusion stones thoroughly before each use and after use. Install an air filter, and ensure a clean air source or the air being fed into the stone is clean, to prevent contaminants from clogging the stone or infecting the wort.
To properly sanitize your stones, we recommend you run them in a sanitized solution for 5 minutes. If the stone becomes clogged we recommend boiling the stone for 1-3 minutes to sanitize & unclog the pores, helping break down anything within it. If boiling is not an option, we recommend soaking in Star San. Star San will remove a majority of surface contamination/bacteria, but will not sanitize the interior of the stone which may or may not be contaminated. If the pores in the aeration stone get blocked from handling give a 15 seconds dip in hydrochloric acid before rinsing with water.
Use sanitized gloves, and don’t touch the porous surface body of the diffusion stone by hand, the oils on your fingers can clog the small pores in the stone.
Can't find a product that meets your needs? Contact our sales staff for OEM/ODM customization services!
